Infrared thermography is the process of using a thermal imager to detect infrared radiation (heat) that is emitted by an object. The technology allows operators to validate normal operations and, more importantly, locate thermal anomalies (abnormal patterns of heat invisible to the eye) which indicate possible faults, defects or inefficiencies within a system or machine asset.
A few examples of where infrared is applied in industrial situations include:
While infrared imaging systems are relatively simple to use, interpreting images taken with this equipment can be far more complex and challenging. With training and experience, however, remarkable information can be extracted from an infrared camera that can help asset managers and maintenance personnel alike better maintain systems and equipment while monitoring or improving the quality of products.
When it comes to inspecting mechanical equipment with infrared, certain conditions are needed. It is also important for the thermographer to have a strong foundation of basic radiometry and heat transfer, knowledge of how the mechanical equipment operates, as well as a solid background on the infrared camera’s capabilities and limitations. As with any type of technology, proper training is essential to successfully operate these systems.
Figure 1: The causes of an abnormally warm motor bearing are not always obvious but infrared is a key means of finding those which are running hot.
Inspecting mechanical equipment with infrared thermography covers a wide variety of systems, everything from motors, rotating equipment, steam traps, refractory, and tank levels and more. Most of these inspections de-emphasize taking absolute temperature measurements and instead concentrate on comparing overall thermal patterns to understand the asset’s health.
Baseline inspections, where a thermographer captures an overall “thermal map” of a particular equipment type, is one of the more valuable uses of the technology, as subsequent inspections are then compared to the original “map” to detail any changes that may have occurred over time. The examples in this article represent only a few of the many areas where IR is utilized for inspecting mechanical equipment in an industrial facility.
While there are many ways to monitor the electrical and mechanical conditions of a motor, thermal imaging has proved itself to be useful mainly as a quick and efficient screening tool. We know that heat is created in any number of ways – by excessive friction, high electrical resistance, reduction of cooling air or fluids and problems with current flow in a motor. If an issue is detected, in the form of an abnormal thermal signature seen in the infrared image – an additional test method such as vibration analysis, airborne ultrasonics or motor circuit analysis – is typically requested to help pinpoint exactly what is causing an anomaly.
Figure 2: Couplings often exhibit strong thermal signatures when there is misalignment or related problems.
Abnormal heating, such as what might occur in a misaligned coupling, could precede a detectable vibration signature. Left alone, such an issue compounds itself as it continues to get worse or even wear on the motor bearing itself. That in turn can also typically be detected with thermography. A variety of issues that are related to the motor’s electrical system may also have thermal patterns associated with them. An internal fault because of the breakdown of insulation on the motor windings can increase the overall temperature of the motor including the motor housing. Often, when the cooling air flow pathways become blocked in a motor, the winding insulation also fails.
Figure 3: Infrared thermography is often used to locate suspected problems in bearings which can then be confirmed with other technologies.
Inspecting bearings is another useful application for infrared thermography. Abnormal friction within a bearing, generating heat, causes the bearing’s surface temperature to rise. This thermal signature, when detected, is an indication of a potential bearing problem, anything from under-lubrication, over-lubrication, poor maintenance or simply a bad bearing. Infrared is especially helpful for inspecting low-speed equipment, including overhead conveyors or idlers, quickly and easily.
Thermography is also used to monitor temperatures on high-temperature refractory insulation such as a rotating kiln, furnace or boiler. Thermal patterns detected in these cases can be used to monitor the condition of the insulation or even calculate the thickness of the remaining refractory. This type of monitoring is invaluable as it facilitates planned maintenance outages and repair of a problem area vs. a catastrophic, and expensive, unplanned failure.
Figure 4: Thermography is a perfect tool for inspecting boiler refractory and air leakage issues. The location of failing refractory can be trended and, when alarm temperatures are determined, repairs can be scheduled.
With the cost of energy increasing, steam traps are another application where infrared thermography can provide valuable savings for a facility. This is accomplished by detecting failures of traps that are stuck open. While airborne ultrasonics is considered a primary test method for this application, infrared inspections can be completed quickly and easily, even at some distance from the device.
A trap that is functioning properly will typically have a large temperature difference between the steam and condensate sides. This temperature difference will temporarily disappear as it cycles. If both sides of the trap are warm it is an indication that the trap has failed open, a condition that can cost literally thousands of dollars in a year.
Both insulation and heat-tracing on process lines can also be inspected with infrared. Applications such as detecting line blockages, monitoring line temperatures, locating damaged or missing insulation can be accomplished with infrared with a few exceptions. Lines covered with very high levels of insulation are more problematic as are process lines that are wrapped with shiny aluminum or stainless steel sheet metal coverings. Inspecting in these situations can be very difficult due to the high thermal reflectivity/low emissivity of the surfaces encountered.
Figure 5: It is possible to locate levels in tanks and silos when they are in thermal transition, providing key information or confirming existing data.
Finally, one of the easier mechanical applications of thermography is to locate levels of gases, liquids, fluidized solids and even sludge in tanks, vessels and silos. Although most storage tanks have a gauge to detect levels, these sensors often fail or must be independently confirmed due to the critical nature of a process.
Similar to inspecting line blockages, the different thermal capacities of solids, liquids, and gases and the way heat moves in and out of them mean these materials change temperature at different rates during a transient heat flow cycle. Gases, having the lowest thermal capacity of them all, typically change most quickly.
Solids, with varying capacitances do not change as rapidly because slower, conductive, heat flow controls the temperature next to the tank wall. Floating materials, including waxes, can usually be distinguished from the liquid due to capacitance differences. Liquids typically take the longest to change because of their high thermal capacitance.
In summary, mechanical infrared inspections can be challenging and rewarding both financially and professionally. The person performing the inspection must have an adequate working knowledge of the equipment they are inspecting as well as sufficient heat transfer theory training to interpret the thermal patterns they observe. As with any predictive maintenance technology, thermography is only one tool in the technician’s toolbox. All the applicable predictive tools should be utilized to give the best possible picture of an asset’s health.
About the authors:
Harold Van De Ven is an instructor and consultant and John Snell is a principal for The Snell Group. For more information on infrared thermography, visit www.thesnellgroup.com.